AIR INTAKE SURROUND | Scania R

Manufacturer: MASKS
SKU: 045S
Cornici Presa d'Aria | Scania RCornici Presa d'Aria | Scania R
  • Description
  • MOUNTING INSTRUCTIONS

AIR INTAKE SURROUND | Scania R

Super mirror stainless steel (aisi 304) application for the air intake of Scania R. Is recommend the use of a good sealing for fixing.

NOTE: Specify if the BUMBER is big or small; specify if the RADAR is mounted on the air intake; specify length of the central AIR INTAKE.

MOUNTING INSTRUCTIONS

DIRECTIONS FOR USE


SURFACE PREPARATION:
SURFACES TO BE SEALED OR BONDED SHOULD BE CLEAN AND DRY. SURFACES SHOULD BE FREE FROM GREASE, MOLD RELEASE, OIL, WATER/CONDENSATION, AND OTHER CONTAMINATES THAT MAY AFFECT THE ADHESION OF THE SEALANT. ABRADING WITH 180 TO 220 GRIT ABRASIVE FOLLOWED BY A SOLVENT WIPE WILL IMPROVE THE BOND STRENGTH. SUITABLE SOLVENTS INCLUDE 3M™ CITRUS BASED ADHESIVE REMOVER, 3M™ SCOTCH-GRIP™ SOLVENT NO. 3 OR METHYLETHYLKETONE (MEK). WHEN USING SOLVENTS, USE IN A WELL VENTILATED AREA. PACKAGING BOTH PRODUCTS ARE AVAILABLE IN 10.5 OZ. CARTRIDGES, 400 ML AND 600 ML, FLEX PACKS. COLORS ARE GRAY, BLACK OR WHITE. 3M™ SCOTCH-SEAL™ POLYURETHANE SEALANT 540 IS ALSO AVAILABLE IN BULK CONTAINERS.


NOTE:
ALCOHOL WILL INTERFERE WITH THE CURING PROCESS AND EXTRA CARE MUST BE TAKENWHEN USING ALCOHOL AS A CLEANING SOLVENT TO PREVENT ANY CONTACT WITH THE SEALANT. USE OF A PRIMER IS AN EXTRA STEP AND COST AND WILL DEPEND ON SUBSTRATES AND THE FINAL END USE. USING PRIMER CAN IMPROVE THE CORROSION RESISTANCE OF CERTAIN METALS AS WELL AS IMPROVE THE DURABILITY OF THE BOND WHEN EXPOSED TO HIGH HUMIDITY CONDITIONS. FOR MOST APPLICATIONS HIGH STRENGTH BONDS ON METAL CAN BE ACHIEVED WITHOUT THE USE OF A PRIMER. PRE-TESTING FOR ADHESION IS SUGGESTED TO DETERMINE IF A PRIMER IS NEEDED. THE 3M™ SCOTCH-WELD™ STRUCTURAL ADHESIVE PRIMER EC-1945 B/A WORKS WELL FOR MOST METALS.


APPLICATION:
TO SEAL THE ITEM USE PRODUCTS AS 3M ™ 560 SCOTCH-WELD. PUNCTURE SEAL IN NOZZLE AND KNOCK OUT THE THIN SEAL AT CARTRIDGE BOTTOM BEFORE PLACING IN CAULKING GUN. (FOR FLEX PACKS CUT OFF THE SMALL CRIMP AT THE END AND THEN PLACE IN CAULKING GUN BARREL WITH THE OPEN END UP). ASSEMBLE TIP AND RETAINING RING ON GUN, CUT TIP TO DESIRED SIZE. PRODUCT SHOULD BE USED WITHIN 24 HOURS AFTER SEAL IS PUNCTURED AND SHOULD BE PRESSED FIRMLY INTO THE JOINT TO ENSURE ADEQUATE CONTACT OF THE SEALANT WITH THE SUBSTRATE. APPLY PRODUCT WHEN TEMPERATURES ARE BETWEEN 40°F (4°C) AND 100°F (3°C). DO NOT APPLY ON FROZEN SURFACES OR WET SURFACES. DO NOT APPLY OVER SILICONES OR IN THE PRESENCE OF CURING SILICONES. AVOID CONTACT WITH ALCOHOL AND SOLVENTS DURING CURING. SEALANT CAN BE TOOLED IMMEDIATELY AFTER APPLYING TO GIVE DESIRED APPEARANCE.


CLEANUP:
WHILE SEALANT IS STILL SOFT CLEANING CAN BE DONE WITH THE SAME SOLVENTS USED FOR SURFACE PREPARATION. IF SEALANT IS ALREADY CURED, REMOVAL IS DONE MECHANICALLY WITH RAZOR KNIFE, PIANO WIRE, SANDING OR 3M™ SCOTCH-BRITE™ MOLDING ADHESIVE AND STRIPE REMOVAL DISC. THIS DISC IS AVAILABLE FROM 3M AUTOMOTIVE AFTERMARKET DIVISION.

Current Stock Level:
0

TORNA AL CATALOGO

NEWSLETTER

Log in

create an account

fb iconLog in with Facebook